Exploring Plumbing Fundamentals for Installing a Bathtub
Exploring Plumbing Fundamentals for Installing a Bathtub
Blog Article
Do you find yourself searching for information about How to Install a Bathtub?
Mounting a bath tub isn't exactly brain surgery, however it does call for solid plumbing, carpentry, and occasionally, tiling skills. Replacing an old bathtub with a new one is also a moderately difficult task. If the old bathtub is easily available, the project can relocate easily; if you need to open a wall surface to eliminate the old tub and also position the brand-new tub, the task is a lot harder. In either case, the job is within a home handyman's abilities, although you will require an assistant to move out the old bathtub and set in the brand-new one. Make sure you have qualified yourself for the work and also fit trying it. As opposed to working with a contractor to take control of a halfway-completed job, it is much better to think about employing one before you begin. Opportunities are you may require a professional plumber to make tube connections.
This write-up will certainly assist you set up a new tub in your shower room if you have already bought a brand-new bathtub as well as don't require to alter the arrangement of your previous water supply pipelines.
Your tools and product checklist need to make up the following:
Getting ready for the Setup
To start with, the supporting frame supplied with the bath ought to be fitted (if required) according to the producer's guidelines. Next off, fit the taps or mixer to the bathtub. When suitable the faucet block, it is necessary to make certain that if the faucet features a plastic washer, it is fitted between the bathroom and also the faucets. On a plastic bathroom, it is likewise practical to fit a supporting plate under the taps unit to prevent stress on the bath tub.
Fit the versatile tap adapters to the bottom of the two faucets using 2 nuts as well as olives (in some cases provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet with the hole in the bathroom. Make use of the nut supplied by the maker to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the flexible overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bathroom. Make certain you make use of all of the supplied washers.
Link the trap to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a similar manner.The bath must now be ready to be suited its final position.
Removing Old Touches
If you need to change old faucets with brand-new ones as a part of your installation, then the first thing you ought to do is disconnect the water supply. After doing so, switch on the taps to drain pipes any water staying in the system. The procedure of removing the existing faucets can be quite troublesome because of the limited accessibility that is commonly the case.
Utilize a basin wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipes to the faucets. Have a fabric all set for the staying water that will come from the pipelines. When the supply pipelines have been gotten rid of, use the same device to loosen the nut that holds the taps onto the bath/basin. You will need to quit the solitary taps from turning throughout this procedure. Once the taps have actually been eliminated, the holes in the bath/basin will need to be cleaned up of any old securing compound.
Prior to going on to fit the new faucets, compare the pipeline connections on the old faucets to the new taps. If the old faucets are longer than the new faucets, after that a shank adapter is needed for the new taps to fit.
Setting up the Tub
Using both wood boards under its feet, position the tub in the needed position. The wooden boards are valuable in uniformly spreading the weight of the bath tub over the location of the boards rather than concentrating all the weight onto four small factors.
The next objective is to make sure that the tub is leveled all round. This can be achieved by examining the spirit level as well as changing the feet on the bath tub till the spirit level checks out degree.
To install taps, fit the bottom of the outermost adaptable faucet connector to the appropriate supply pipeline by making a compression sign up with; then do the very same for the various other tap.
Activate the water system as well as examine all joints as well as new pipework for leakages and tighten them if needed. Fill the bath tub and likewise inspect the overflow outlet and also the normal electrical outlet for leakages.
Ultimately, repair the bath paneling as described in the producer's instruction manual. Tiling and securing around the bathtub should wait till the bath tub has been used at the very least when as this will resolve it right into its last setting.
Suitable New Taps
If the tails of the new taps are plastic, then you will certainly require a plastic adapter to stop damages to the string. One end of the connector fits on the plastic tail of the faucet and the various other end provides a connection to the existent supply pipelines.
If you require to fit a monobloc, after that you will require minimizing couplers, which attaches the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
Next off, position the faucet in the placing opening in the bath/basin making certain that the washing machines are in area in between the tap and the sink. Protect the faucet in position with the producer supplied backnut. When the faucet is firmly in position, the supply pipes can be connected to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with typical tap adapters. The previous kind must be connected to the tap ends initially, tightening up only by hand. The supply pipes can later be linked to the various other end. Tighten up both ends with a spanner after both ends have been connected.
Tiling Around the Tub
In the location where the bath satisfies the tile, it is required to seal the joins with a silicone rubber caulking. This is very important as the installation can relocate enough to break a stiff seal, causing the water to penetrate the wall in between the bathroom as well as the tiling, resulting in problems with wetness and also possible leaks to the ceiling listed below.
You can select from a variety of coloured sealers to blend in your fixtures and also installations. They are sold in tubes and also cartridges, and can securing voids up to a width of 3mm (1/8 inch). If you have a larger space to fill up, you can fill it with spins of soaked paper or soft rope. Keep in mind to always fill up the bath tub with water prior to sealing, to permit the movement experienced when the bathtub remains in use. The sealer can fracture relatively very early if you do not consider this motion prior to securing.
Conversely, ceramic coving or quadrant floor tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are additionally conveniently readily available on the marketplace. It is a good idea to fit the floor tiles utilizing water-resistant or water resistant adhesive and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We are very interested by How to Install a Bathtub Yourself and I am hoping you liked my blog entry. So long as you enjoyed reading our blog posting kindly be sure to pass it around. Thanks a bunch for your time. Please visit our website back soon.
Source This Article Report this page